Plywood, formwork locks, galvanized wire and building materials.
Galvanized wires are produced in accordance with international standards. For these products; – Zinc coating amount compliant with standards – Bright appearance – Homogeneous coating – Good adhesion of the galvanized layer to the wire surface – Smooth outer surface are important, and in line with customer requirements, hot-dip
When a steel rod is used instead of a tie bolt to fix shear walls, columns and beam forms opposite each other; it is fitted onto both ends of the rod to prevent the formwork from opening. Thanks to its steel toothed spring-loaded latch, it safely clamps and holds the steel rod tight.
WHAT IS PLYWOOD? Plywood consists of film-faced plywood panels formed by pressing thin layers of wood under high pressure. Film-faced concrete formwork plywood, known in the industry as Plywood, is manufactured from durable woods such as pine, beech and birch. The glue used in making plywood
Ravago Building Solutions
A two-component, high-strength rigid silicone adhesive developed for insulating glass applications that demand high mechanical performance and stiffness.
A two-component silicone sealant used as the secondary seal in insulating glass units.
A two-component structural glazing silicone developed for structural facade applications, with superior adhesion to a wide range of substrates.
A single-component, neutral-cure silicone adhesive for the structural bonding of glass, metal and other building components.
A single-component, neutral-cure, low-modulus silicone weatherseal for facade and curtain wall joints.
A single-component neutral-cure silicone sealant for PVC-U, glass, coated substrates and masonry applications.
A specially formulated solvent-blend cleaner for surface preparation prior to bonding applications.
A surface primer consisting of a dilute solution of moisture-reactive components in a volatile siloxane, used to prepare substrates before silicone bonding and sealing.
A fire-resistant, one-component, self-curing firestop silicone sealant offering ±50% joint movement capability.
A paintable, water-based, one-component intumescent acrylic firestop sealant that expands at high temperatures to protect against flame and smoke.
A fast-curing, one-component silicone panel adhesive developed for bonding facade panels to their frames.
A one-component polyisobutylene, solvent-free and non-reactive primary butyl sealant for insulating glass units.
A one-component polyisobutylene primary butyl sealant with high temperature resistance, showing no leakage or flow at temperatures up to 95–100 °C.
Mega Insulation Solutions
A high load-bearing, lightweight EPS fill material used in ground improvement applications.
A lightweight, load-bearing composite lintel system used to span door and window openings.
A cement-based, normal-setting class C1 adhesive mortar for bonding ceramic, tile and natural stone coverings in interior and exterior applications.
A cement-based adhesive mortar certified to TS 13566 for bonding thermal insulation boards to the substrate.
A lightweight, class A1 non-combustible insulation element designed to eliminate thermal bridges at columns and beams.
A cement-based ready-mixed rough plaster mortar applied by hand to wall and ceiling surfaces indoors and outdoors.
A cement-based thermal insulating plaster mortar with enhanced adhesion and a thermal conductivity of 0.18 W/mK.
A masonry block that integrates a rock wool layer into the block body, delivering wall construction and thermal insulation in a single operation.
A cement-based adhesive mortar with 0.26 W/mK thermal conductivity, developed for thin-bed laying of insulating blocks.
A cement-based ready-mixed rough plaster mortar prepared for machine application on interior and exterior wall and ceiling surfaces.
A masonry block with integrated rock wool whose layered structure delivers superior sound insulation at minimum wall thickness.
Dalsan Alçı
Bagged machine-applied gypsum plaster that finishes brick, concrete and aerated concrete surfaces in a single coat without a satin skim.
Machine-applied gypsum plaster whose lightweight formulation covers the same area at only 7,5 kg/m², ready for paint in one coat.
Economical machine plaster of the low gypsum content lightweight class, delivering high surface hardness.
Bagged machine gypsum plaster offering over 100 minutes of pot life and a paint-ready surface in a single coat.
Machine gypsum plaster sprayed directly onto brick, concrete and aerated concrete, delivering a paint-ready surface in one coat.
Concentrated machine plaster whose 26 kg bag covers the same area as a standard 35 kg bag, cutting transport and handling loads.
Hand-applied perlite gypsum plaster that does not slump or sag, laid in a single 5-40 mm coat on walls.
Hand-applied perlite gypsum plaster laid 8-15 mm on brick and 5-10 mm on aerated concrete, with no slumping.
Hand-applied perlite gypsum plaster laid 10-30 mm on wall surfaces without slumping or sagging.
Fine finishing plaster that fills cracks and irregularities on plastered or plasterboard surfaces, preparing them for satin skim.
Satin finish plaster applied over plastered surfaces and COREX gypsum boards to create a hard, smooth substrate for paint.
A high-adhesion finishing skim plaster that creates a smooth, paint-ready surface on gypsum plaster and plasterboard.
A ready-mixed, gypsum-based machine plaster delivered to site by silo tanker.
A building plaster for casting and fixing decorative gypsum elements such as cornices, ceiling roses and niche mouldings.
A gypsum-based bonding compound for fixing plasterboard, EPS, XPS, mineral wool and insulated composite panels to wall surfaces.
A flexible gypsum jointing compound used with joint tape at COREX plasterboard joints to produce a smooth, seamless finish.
An acrylic-based green plaster primer that keys smooth concrete surfaces to improve the adhesion of gypsum and cement-based renders.
Galvanised perforated corner bead that squares wall corners and improves impact resistance.
An expanded-wing galvanised steel bead that keeps directly plastered wall corners true and improves their impact resistance.
A cement-based ready-mixed machine render delivered by silo tanker and spray-applied to interior and exterior surfaces.
A cement-based ready-mixed render for interior and exterior use, applied by spray machine or by hand.
A low-consumption cement-based ready-mixed machine render that covers the same area with less material.
Polymer-modified, single-component cement-based joint filler and base coat render for exterior cladding boards.
White cement-based decorative top coat render with mineral grain texture under 2 mm, applied by trowel.
Cement-based skim coat that smooths interior and exterior render surfaces prior to painting.
Cement-based, polymer-modified repair and levelling mortar for deep cracks and holes in fair-faced concrete.
High-performance cement-based masonry mortar for thin-bed laying of aerated concrete blocks.
High-performance cement-based masonry mortar for laying brick and pumice blocks.
Class C1T cement-based tile adhesive for ceramic, glass mosaic and wall tile coverings.
Class C1TE cement-based tile adhesive with extended open time.
Class C2TE adhesive for horizontal and vertical interior and exterior application of coverings including porcelain and granite tiles.
Deformable, slip-resistant class C2TES1 adhesive for pools, wet areas and underfloor-heated floors.
Cement-based, polymer-modified CG2 A class tile grout for joints up to 6 mm wide in ceramic and tile finishes.
Cement-based, polymer-modified, water-repellent CG2 WA class flexible tile grout for joints up to 6 mm wide, indoors and outdoors.
Standard Type A gypsum plasterboard to TS EN 520 +A1 for partition walls, wall linings and suspended ceilings.
Gypsum board that is 17% lighter than standard COREX at 6,66 kg/m2, ideal for suspended ceiling applications.
New-generation standard gypsum board with a reinforced core, weighing 6,35 kg/m2 for ergonomic handling.
Moisture-resistant gypsum board of type H1 - H2, with a water-repellent core, for wet areas.
Moisture-resistant gypsum board 17% lighter than standard Green COREX, at 6,66 kg/m2.
Type DF gypsum board with increased density and fire resistance, its core reinforced with special fibres and additives.
Type FH2 gypsum board for areas requiring both moisture resistance and fire resistance.
Glass-tissue faced, fibre-reinforced gypsum board classified A1 non-combustible for high fire performance.
Type D high-density gypsum board, 35% heavier than standard boards, for improved sound insulation.
Type DIR gypsum board with increased impact resistance and density, around 70% heavier than standard boards.
Higher-density standard gypsum board with improved sound insulation performance.
Denser moisture-resistant gypsum board with reduced water absorption.
High-density impact-resistant gypsum board with increased surface hardness and fire resistance.
Perforated acoustic gypsum board that reduces reverberation.
High-strength galvanised drywall profile range produced with emboss technology.
Galvanised ceiling U track for wall lining and suspended ceiling systems.
Galvanised ceiling C furring channel that carries the plasterboard in ceilings and linings.
Galvanised wall U track forming the floor and head connection of partitions and linings.
Galvanised wall C stud forming the vertical framing of partitions and wall linings.
2 mm thick support profile with fixing set that reinforces door and window openings in drywall systems.
Galvanised connection components completing plasterboard wall lining and suspended ceiling systems.
Galvanised suspension rod that links the ceiling grid to the soffit above, produced in 7 different lengths.
Jaw hanger that clips onto the suspension rod and grips the main ceiling C-channel (TC).
Connecting clip that fixes secondary channels to the main furring channels by folding over them.
Splice connector that joins ceiling C-channels (TC) end to end to form a continuous run.
Fixing bracket that replaces the suspension rod in shallow plenums and is also used in wall linings.
Black phosphate, sharp point screw fixing plasterboard to 0.50–0.70 mm galvanised profiles.
Drill point, black phosphate drywall screw for galvanised profiles 0.70–2.00 mm thick.
Purpose-designed 32 mm screw for fastening two COREX plasterboards to each other.
15 mm zinc plated metal-to-metal screw for fixing agraf brackets to ceiling C-channels (TC).
Self-adhesive glass fibre jointing tape that prevents cracking at plasterboard joints.
Paper jointing tape made from special paper, supplied in 150 m rolls for plasterboard joints.
Self-adhesive polyethylene tape bonded under profiles to break acoustic bridges.
Galvanised metal-reinforced paper corner tape that keeps drywall corners straight and impact resistant.
Plastic wall plug and washer-head screw set for fixing galvanised profiles to floors, ceilings and walls.
High-strength steel anchor fixed to the existing slab in suspended ceiling systems.
Purpose-designed cavity fixing for hanging pictures, shelves, cabinets and radiators on plasterboard walls.
Grooved self-drilling drywall anchor for fixing pictures, shelves and cabinets to plasterboard walls.
Spring toggle anchor for suspending chandeliers and similar items from plasterboard ceilings.
Push-latch hinged access panel providing easy entry to services behind ceilings and walls.
Lay-in access panel lifted by hand to reach services within the ceiling void.
Glass-mat faced exterior sheathing board with a moisture-resistant core for external wall construction.
White glass-mat faced gypsum board with a moisture-resistant core for interior and exterior use.
A1 non-combustible roof sheathing board used instead of OSB or timber beneath tiles and shingles.
0.9 mm galvanised facade stud used on the outer frame of exterior drywall systems.
Galvanised 0.60 mm DC stud profile forming the load-bearing frame of exterior drywall facade systems.
0.90 mm galvanised facade profile that carries the sheathing board in Jacket and JacketMAX cladding systems.
0.50 mm galvanised omega section that ties two DC studs together in double-frame, Jacket Omega and Omega systems.
1.2 mm galvanised adjuster bracket that plumbs the facade and allows thicker mineral wool in the JacketMAX system.
0.60 mm galvanised support channel onto which AL160 and AL210 adjusters are fixed in the JacketMAX system.
0.50 mm galvanised corner profile screwed from the inside to increase impact resistance at facade corners.
2 mm L bracket made of low thermal conductivity special steel that plumbs the facade substructure.
Corrosion-resistant screws tested for 1000 hours in salt spray, designed to fix exterior sheathing boards to steel profiles.
Self-adhesive alkali-resistant joint tape for the board joints of exterior sheathing.
160 g/m2 glass fibre reinforcement mesh that prevents cracking caused by movement of cement-based render.
3 m PVC starter profile that separates the exterior sheathing board from the ground.
PVC corner bead that can be formed to any radius and increases impact resistance on curved corners.
PVC-based corner profile with mesh on both wings, used in exterior drywall facades to increase the impact resistance of door and window corners.
PVC-based reveal profile with mesh on both wings, ensuring straight and crack-free architectural joints on facades.
PVC-based reveal profile without mesh, used to form clean and trouble-free architectural joints on facades.
PVC-based drip bead with mesh on both wings, directing water away from the facade at soffits and above window and door openings.
Ready-mixed acrylic-based jointing, repair and finishing compound for plasterboard joints and all interior surfaces.
Machine-applied, easy-flowing ready-mix floor screed for concrete slabs; applied at a minimum thickness of 20 mm and walkable after 2 hours.
Ready-mixed self-levelling floor screed applied at 2-10 mm indoors to prepare the substrate before the final floor covering.
Green, modified synthetic resin based interior floor primer that improves substrate adhesion and prevents air bubbles before self-levelling screed application.
Bostik
Two-component epoxy moisture-barrier membrane applied to the substrate before floor coverings.
Two-component, solvent-free epoxy repair kit for filling cracks and joints in reinforced concrete floors.
Cement-based, ready-to-use dry screed for interior and exterior floors.
Acrylic dispersion mounting adhesive with instant grab for decorative and insulation boards.
One-component, moisture-curing polyurethane adhesive and sealant with rapid cure.
Very-low-VOC acrylic adhesive for all resilient floor coverings, developed especially for LVT and rubber.
Solvent-free polymer dispersion adhesive forming a permanently tacky film for removable carpet tiles.
Solvent-based neoprene contact adhesive for interior floor and wall coverings.
Non-yellowing, 100% pure acetic silicone sealant with extended service life for sanitary joints.
One-component, paintable acrylic polymer mounting and joint sealant.
Cement-based tile adhesive of class C1TE produced to TS EN 12004.
Fast-setting, self-levelling cement-based grout mortar for fixing steel structures, reinforcement and machine bases to concrete.
One-component, moisture-curing polyurethane adhesive with fast cure and excellent adhesion to metal, glass, ceramics, timber and many plastics.
Two-component epoxy resin anchoring mortar and adhesive for rebar dowelling, anchor setting and metal fixing.
One-component, moisture-expanding and curing aerosol PU foam with straw adaptor for door and window frame installation and gap filling.
Double-sided HDPE adhesive foam tape that provides initial hold and the correct adhesive thickness when bonding cladding panels.
One-component acrylic resin based liquid concrete curing compound for fresh concrete and hardener-treated floors.
Cement-based thin-bed masonry adhesive mortar for aerated concrete and porous brick walls.
Polysiloxane-based, acetoxy-curing red high-temperature silicone sealant resistant to 200°C continuous and 300°C intermittent heat.
Fast-curing one-component polyurethane joint sealant that does not bubble while curing.
Oxime-based neutral facade silicone for versatile interior and exterior use.
One-component neutral silicone based adhesive developed for bonding EPDM membranes.
Polysiloxane-based heat-resistant liquid gasket sealant for engine components.
Cement-based skim plaster to TS EN 998-1 that provides a paint-ready surface indoors and outdoors.
SMP-based primer that improves the adhesion of sealants to absorbent and porous substrates.
Cement-based dry-shake floor hardener with quartz and corundum aggregate for fresh concrete.
Solvent- and isocyanate-free, overpaintable SMP-based multipurpose joint sealant.
Cement-based floor hardener with corundum aggregate only, offering very high abrasion resistance.
Transparent wipe-on primer that increases adhesion strength on cladding panels and metal surfaces while also acting as a cleaner.
Single-component SMP-based hybrid elastic adhesive, free of solvents, silicone and isocyanates.
Class R1 cement-based thick repair mortar to TS EN 1504-3, fibre-reinforced with improved crack resistance.
Class C2TES2 tile adhesive to TS EN 12004; extra flexible, high-strength, with extended open time.
Thixotropic, non-shrink, high compressive strength cement-based anchoring and grouting mortar.
100 % pure, non-yellowing acetic silicone sealant developed for shower cabin installation.
Gun-applied, moisture-curing general purpose aerosol polyurethane foam.
Class R2 polymer-modified, high-strength cement-based concrete filling and repair mortar to TS EN 1504-3.
Ready-to-use universal dispersion primer in transparent white that balances substrate absorbency.
Professional hybrid assembly adhesive with extremely high initial grab.
Acrylic polymer based, extra flexible joint sealant that can be painted once dry.
Polysiloxane based, moisture-curing acetic universal sealing silicone.
Class C1 cement based ceramic tile adhesive to TS EN 12004, for interior floors.
Alkoxy based, neutral-curing flexible façade silicone developed for exterior joints.
Acrylic polymer based, silicone emulsion modified, paintable joint sealant.
White-cement based, high strength surface repair and smoothing mortar for a fine finish on concrete.
Single-component, long-life butyl sealant based on a butyl and vegetable oil blend.
Polysiloxane based, neutral-curing silicone developed for marble and granite joints.
SMP based, moisture-curing, highly elastic adhesive for bonding exterior façade cladding panels.
An acrylic-based absorption-regulating primer dispersion used on absorbent and porous substrates before levelling and smoothing.
A versatile acrylic-based bonding primer that increases the adhesion of self-levelling compounds and tile adhesives on non-absorbent substrates.
A solvent-free, odourless, water-based adhesion-promoting sanding primer that improves the bond of self-levelling screeds on non-absorbent substrates.
A cement-based fine repair mortar for surface levelling and repair work on interior and exterior façades, non-cracking and with excellent water vapour permeability.
A fast-drying, cement-based dry screed with rapid setting and drying properties, used to form bonded and floating screeds.
P580 SUPERGRIP XTRA POWER is a solvent-free, EN 204/205 D4 waterproof polyurethane construction adhesive with a shear strength of up to 12 N/mm².
A class C1T cement-based adhesive mortar produced to TS EN 12004, used for fixing ceramics, tiles and mosaics to walls and floors.
A super-fine, white cement-based skim coat plaster manufactured to TS EN 998-1 for obtaining paint-ready surfaces.
A CG1 class, cement-based flexible tile grout to TS EN 13888, developed for narrow joints.
An R4 class thixotropic, fibre-reinforced, cement-based structural repair mortar to TS EN 1504-3 for vertical applications.
A one-component aerosol polyurethane foam that expands and cures with atmospheric moisture, designed for straw application.
A solvent-free, two-component epoxy repair compound for bridging cracks in reinforced concrete floors.
A high-quality hybrid-based sealant and high-strength adhesive, free of isocyanate, solvent and silicone, for interior and exterior use.
A ready-to-use, cement-based floor hardener with quartz aggregate only, broadcast monolithically onto fresh concrete.
A polysiloxane-based neutral cure silicone adhesive developed specifically for bonding float glass mirrors.
A polysiloxane-based, air-curing acetic sealant for bathroom, kitchen and joinery joints.
A solvent-free, free-flowing two-component epoxy adhesive used to bond old and new concrete.
General-purpose, very strong and transparent hybrid adhesive.
Class R4 flowable, cement-based structural repair mortar to TS EN 1504-3.
One-component, moisture-curing polyurethane sealing and jointing mastic.
Class C2FTE fast-setting, high-strength flexible tile adhesive to TS EN 12004.
Copolymer dispersion based liquid synthetic rubber bonding admixture for cementitious mortars.
One-component, moisture-curing SMP based elastic adhesive for facade panels.
Class R1 cement-based thick-layer repair mortar to TS EN 1504-3.
Flexible assembly adhesive based on SMP hybrid technology with instant grab, bonding without mechanical fixing.
Fibre-reinforced, fast-drying and paintable self-levelling screed for interior floors, applied at 1-10 mm.
Polymer-modified cement-based self-levelling floor screed for high build-ups, applied at 5-40 mm.
Standard high-flow self-levelling floor screed for interior floors, applied at 1-10 mm.
Multi-purpose water-based acrylic flooring adhesive for homogeneous and heterogeneous PVC, carpet and natural fibre coverings.
Hybrid self-levelling screed in class C20-F6 based on calcium sulphate, cement and modified polymer binders.
Mould-resistant acetoxy silicone sealant for kitchen, bathroom and shower applications.
Neutral oxime silicone sealant with high movement capability, developed for glazing and facade joints.
Plasticiser-free general-purpose hybrid adhesive and sealant that does not stain natural stone.
Solvent-free acrylic dispersion mounting adhesive for bonding timber, chipboard, uPVC and EPS/XPS decorations indoors.
One-component high-strength polyurethane adhesive whose thixotropic consistency also suits vertical applications.
Paintable, economical and high-quality water-based acrylic sealant for interior connection joints.
One-component durable mastic based on a blend of butyl and vegetable oil.
Self-adhesive butyl tape used to achieve airtight sealing.
Acetoxy-based silicone for glazing and façade joints.
Multi-purpose acetoxy-based silicone for glazing and façade joints.
Acetoxy-based silicone with high temperature resistance.
Contact us for a free survey, technical consultancy and a fast quote.
444 74 91
0531 734 37 11
info@niltiritoglu.com.tr
Demirciler Sitesi Samsun Yolu No:46 Siteler / Ankara
